include/gaudi/asic_reg/nic0_tmr_regs.h | 184 + include/gaudi/asic_reg/gaudi_regs.h | 26 +. misc/habanalabs/include/common/cpucp_if.h | 34 +. misc/habanalabs/gaudi/gaudi_nic_ethtool.c | 616 +++ĭrivers/misc/habanalabs/gaudi/gaudi_phy.c | 1276 +++++ misc/habanalabs/gaudi/gaudi_nic_dcbnl.c | 108 + misc/habanalabs/common/habanalabs_ioctl.c | 151 +-ĭrivers/misc/habanalabs/common/pci.c | 1 +ĭrivers/misc/habanalabs/gaudi/Makefile | 3 +ĭrivers/misc/habanalabs/gaudi/gaudi.c | 957 +++-ĭrivers/misc/habanalabs/gaudi/gaudiP.h | 331 +. misc/habanalabs/common/habanalabs_drv.c | 5 + Habanalabs/gaudi: add NIC init/fini calls from common codeĭrivers/misc/habanalabs/common/context.c | 1 +ĭrivers/misc/habanalabs/common/device.c | 24 +-ĭrivers/misc/habanalabs/common/firmware_if.c | 44 +ĭrivers/misc/habanalabs/common/habanalabs.h | 33 +. Habanalabs/gaudi: Add ethtool support using coresight Habanalabs/gaudi: add WQ control operations Habanalabs/gaudi: add CQ control operations Habanalabs/gaudi: add a new IOCTL for NIC control operations Habanalabs/gaudi: allow user to get MAC addresses in INFO IOCTL Habanalabs/gaudi: add NIC Ethernet support Habanalabs/gaudi: add support for NIC QMANs Habanalabs/gaudi: add NIC security configuration Habanalabs/gaudi: add NIC firmware-related definitions Habanalabs/gaudi: add NIC H/W and registers definitions The only modification from v2 is in the ethtool patch (patch 12). This is the second version of the patch-set to upstream the GAUDI NIC code To: linux-kernel, netdev +Cc: SW_Drivers, gregkh, davem, kuba, andrew, f.fainelli ` (15 more replies) 0 siblings, 16 replies 83+ messages in thread 17:10 ` habanalabs/gaudi: add NIC firmware-related definitions Oded Gabbay Since you configure the VPN device yourself, it's important that you would be familiar with the device and its configuration settings.Adding GAUDI NIC code to habanalabs driver LKML Archive on help / color / mirror / Atom feed * Adding GAUDI NIC code to habanalabs driver 17:10 Oded Gabbay Besides, since Cisco ASA templates are notĬompatible for dynamic routing, please make sure that you chose the static routing. VPN device cannot be located behind a NAT. IPSEC tunnel, you need to allow the ESP protocol and UDP Port 500. You can refer to this article for Cisco ASA templates for Static routing:ĭid you download the VPN configuration file from the dashboard and copy the content of the configurationįile to the Command Line Interface of the Cisco ASDM application? It seems that there is no specified IP address in the access list part and maybe that is why the states message appeared.Ĭisco ASA template, it should be similar to this: Step-By-Step: Create a Site-to-Site VPN between your network and Azure However, you should be able to setup a site-to-site VPN with Cisco ASA 5505 series security appliance as Unfortunately, a dynamic routing VPN gateway is required for Multi-Site VPN, VNet to VNet, and Point-to-Site. The Dynamic routing is not supported for the Cisco ASA family of devices. Thank you for your interest in Windows Azure. As of now, we do not have any scripts for Cisco ASA 9x series.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |